Addictive drums 3 release date windows#

I'm sure some of these could be adjusted better but I had a hard time hearing or feeling the difference with most of the settings. I gave up on trying to get the VH11 setting within the TD-12 to not double trigger with the HH pedal.

I have the HH fairly dialed in now and wanted to share my settings.

A subset of drum pieces can be routed to the bus for further processing, typically heavy compression, and then tastefully mixed into the Master out.Ok.

Note that Room, Bus and Master have their own Channel Strip.

It also indicates вЂњhow muchвЂќ of the drum piece is being sent to each of the 2 Dlerbs

вЂњSendsвЂќ turns on/off the effects sends to the Dlerbs.

вЂњInsertsвЂќ turns on/off the Channel Strip for A/B.

вЂњDecayвЂќ exaggerate or subdue sustain (вЂњtightnessвЂќ).

вЂњBottomвЂќ knob controls additional low end.

вЂњDriveвЂќ knob controls amount of analog tape effect.

These are adjusted by dragging the 4 circles on the graph.

Each band has readout which shows mid-frequency, gain/reduction, and Q value.

Bandpass filters adjusted with triangle on either side of graph.

Once selected, you can drag the frequency selection-field up or down by dragging the central bar.

Graph adjusts frequency of distortion by raising or lowering the bottom or top slider.

Right/left arrows select various types of distortion sources.

Slider вЂ“ sets the threshold for compressor.

Compressor вЂ“ Distortion module (NOTE that this module вЂњflipsвЂќ with the вЂњTape and ShapeвЂќ module such that you can have either (or both) pre or post the EQ module).

Decay вЂ“ how long the noise sustains (i.e., вЂњtailвЂќ).

Noise вЂ“ the arrows select different noise generators (tube, vinyl, etc.).

on the snare there is a top slider that adjusts how much snare noise bleed occurs in other drums (i.e., real world sound).

only the kick and snare have 2 mics and the balance between these is adjusted with the slider below.

Strip is semi-independent from Sampler Strip however, making a selection on the mixer will focus both the Sampler and Channel strip on same drum. Once selected, you can drag the selection-field up or down by dragging the central bar.

Control filter by raising or lowering the bottom or top slider.

Adjust attack, sustain, delay, release by dragging the 4 little circles about on the graph.

Addictive drums 3 release date windows#

3 windows (start, decay, end) adjusted by clicking and dragging are useful to dampen/exagerate ring.

вЂњVelвЂќ slider вЂ“ only applies effect to specific range of velocities.

Beneath the graph are 3 windows (start, hold, and end), which are adjusted by clicking and dragging on these windows.

Pitch Envelope вЂ“ adjusts tone over time.

OH/Room вЂ“ adjusts tone up/down but only in Overhead and Room mics.

Filter вЂ“ low pass filter, cuts higher frequencies of lower velocity hits making them duller.

Volume (of lower velocities) - Counter-clockwise makes lower velocities louder, clockwise makes lower velocities softer.

Response Slider вЂ“ limits the pool of hits by raising or lowering the bottom or top slider.NoAlts вЂ“ defeats the alternate hits, all hits sound the same.Far left panel selects drum to edit, and send levels to the Overhead and Room mics.As far as Mixer Channel Outputs, all should be sent to the Master Out unless external plug-ins are desired (e.g., the snare). It is possible to copy the entire top row settings and paste those to another drum piece by right clicking alternatively, copy and paste just one section to another drum.